This article includes a, related reading or, but its sources remain unclear because it lacks. Please help to this article by more precise citations. ( September 2014) () ccTalk (pronounced see-see-talk) is a protocol in widespread use throughout the money transaction and industry. Kniga receptov dlya muljtivarki polaris pmc 0508d. Such as the for coins and banknotes found in a diverse range of automatic payment equipment such as transportation, ticketing, payphones, amusement machines, and retail cash management use ccTalk to talk to the host controller. The ccTalk protocol is one of 2 protocols specified by for use in all AWP machines with serial coin acceptors.

(The other is the Host Intelligent Interface protocol developed by ).: 20 The protocol was developed at a company called Coin Controls (hence coin-controls-talk, later called Money Controls and from 2010 Crane Payment Solutions) on the outskirts of in north-west mainly by Engineer Andrew William Barson. The first release of the protocol was in 1996.

The ccTalk protocol is an.: 13 The protocol uses an asynchronous transfer of character frames in a similar manner to RS232. The main difference is that it uses a single data line for half-duplex communication rather than separate transmit and receives lines. It operates at and is ‘multi-drop’ i.e. Peripherals can be connected to a common bus and are logically separated by a device address. Each peripheral on the ccTalk bus must have a unique address. The original protocol operated at 4800 with subsequent releases standardising on 9600 baud. Low cost bridge chips are now available from a number of manufacturers to allow ccTalk to run over USB at baud rates of at least 1 Mbit/s.

CcTalk® PC Interface User Manual TSP076.doc Issue 1.0 – May 2003 This document is the private unpublished property of Money Controls Ltd and may not be reproduced in part or in total by any means, electronic or otherwise, without the written permission of Money Controls Ltd. Money Controls Ltd does.

CcTalk protocol stacks have been implemented on a range of devices from tiny with 512 of to powerful 32-bit processors.: 12-13 The protocol supports all standard operations for electronic devices such as upgrading of firmware, secure transfer of data and detailed diagnostic information. Advantages of ccTalk include low cost technology, a simple-to-understand packet structure, an easily expandable command interface and no licensing requirements. The latter affords the protocol a good deal of popularity in a crowded and highly competitive field similar to open-source software.

In 2010, encryption was added to certain commands so that it could be made more resilient against attacks on the bus. Each peripheral has its own unique DES key. Contents • • • • • An Example ccTalk Message Packet [ ] TX data = 2 0 1 245 8 • 2 = destination address • 0 = zero data bytes • 1 = source address • 245 = command header ‘Request equipment category id’ • 8 = checksum ( 2 + 0 + 1 + 245 + 8 = 256 = 0 mod 256 ) This is a message from address 1 ( the host ) to peripheral address 2 to find out what it is. RX data = 1 13 2 0 67 111 105 110 32 65 99 99 101 112 116 111 114 22 • 1 = destination address • 13 = 13 data bytes • 2 = source address • 0 = reply header • 67114 = ASCII for ‘Coin Acceptor’ • 22 = checksum ( sum of all packet bytes is zero ) The reply from address 2 back to address 1 identifies it as a coin acceptor. Details [ ] The ccTalk protocol is a byte-oriented protocol.

The series of bytes in a message -- represented above as a series of decimal numbers -- is transmitted as. Many devices have single electrical connector that carries both power (typically +12 V or +24 V) and the ccTalk data over a total of 4 wires.

To reduce cost, for short interconnection distances CPI recommends sending ccTalk data over an unbalanced open-collector interface: both transmit and receive messages occur on the same bi-directional serial DATA line at, driven through an open-collector NPN transistor.

>: Pescara Converter The Pescara Bill Acceptor Multi-Protocol Converter, product code MAPIRB, is a small, low-cost unit designed for those machine manufacturers and operators who have host systems (games, kiosks, change machines etc.) which currently use a bill acceptor using one interface / communications protocol, but who now wish to use a new bill acceptor that is only available with a different interface. The current version connects note / bill acceptors that use the ID003 or ccTalk serial protocols to games / systems that use the Ardac 2, 'Mars Vend Serial', ccTalk or GPT V2.2 protocols, but many other variants can be easily produced. The host protocols that we have implemented are carefully designed and implemented such that your machine should be unable to detect any differences between your existing bill acceptor and this protocol converter. Physically, the Pescara Bill Acceptor Converter is an 8cm square package, with 4 data connectors: 2 x RS232 interfaces, a ccTalk interface and a Mars Vend Serial interface. Of these the appropriate two will be used in your particular application. The converter unit is configured at installation by changing a small, rotary switch.