Accufast KT2 Tabber The Tabletop Tabber Series That Revolutionized the Industry The Accufast KT2 tabber is similar to the KT with the addition of another tabbing head, which allows you to apply one or two tabs in one pass. Rags max schneider someday download free. The Accufast KT tabber series are crash tabbers in which the edge of the piece to be tabbed is fed into the machine first. The leading edge then comes in contact with the tab which has been fed down in front of the piece, pulling the tab from its backing paper. When you pair the Accufast KT2 tabber with the FX Feeder and 3FV conveyor, you have the most reliable tabbing system out there today. All Accufast are proudly made in the USA. The ACCUFAST KT2 is a feature rich basic tabbing machine. It uses plain circular or rectangular tabs either opaque or clear.

Accufast Kt Tabber User Operators Manual. Accufast Tabber. Accufast Tabber. Kt Timing Belt, 3mm Pitch, 9mm Wide, 02-1590-00 New. Getinge 8 - $7.50.

It tabs pieces up to 1⁄4” in thickness and it rolls the waste up on a take up spool. At speeds of 15,000 per hour or so, it is a stretch to refer to the ACCUFAST KT2 as a basic tabber – there’s a lot of the professional in the KT2. Advantages of Accufast KT2 Crash Tabbers • High productivity. The shortest dimension feeds through the machine increasing production rates at any given speed • Simplicity. Short paper path with no skewing adjustments etc. Tabs fold tight to the edge of the piece and do not drift from left to right.

• Ideal for off-line applications. Accufast KT2 Tabber Technical Specifications • applies 1 or 2 tabs per piece • tabs 15,000+ pieces per hour • tabs pieces 5” to 16” wide, from 20 lb. Thin to 1/4” thick, coated and uncoated • runs a variety of 1” tabs: paper & frosted, circles & rectangles, on rolls with or without tractor holes • built-in waste take-up spool • weighs 56 pounds • measures 11”l x 19”h x 23”w • uses 115 volts 2 amps 60 hz or 230 volts 1 amp 50 hz • goes in-line with ACCUFAST and other tabletop Labelers and Printers • its outstanding feature is a pair of independent tabbing heads - turn them both on to twin tab, turn only one on to single tab.

How do I adjust and clean the Accufast KT Tab Sensor? Published: December 3, 2011 UPDATED If you experience tabbing problems on the Accufast KT, tune the sensor for – Also know as a KT Sensor Reset: WARNING DO NOT PLACE FINGERS OR TOOLS BETWEEN OR NEAR MOVING PARTS. 1) Turn the POWER SWITCH off. 2) Remove any tabs and debris from the peel point area through the INSPECTION WINDOW on the input end, below the threading path. CAUTION IF ALL TABS AND DEBRIS ARE NOT REMOVED FROM THE PEEL POINT AREA BEFORE CLEAR TAB IS ACTIVATED, THE SENSOR’S DEFINITION OF CLEAR TABS WILL CHANGE AND CLEAR TABBING WILL BE PREVENTED.

On the product entry side, there is an elongated hole under where the tabs peel off, see below If you look inside the hole, you will see the bottom portion of the sensor. (The black circle in the white plastic, see photo below) Clean it off with some. Also, make sure no tabs are anywhere in the path.

If you remove the tabs and look from the exit side, you can see the top portion of the sensor. In the photo below, look for the rectangle with the nut on it. The sensor is on the bottom of the white housing directed down at the lower sensor. Once you have this area clean turn the KT back on and, 3) Toggle CLEAR TAB off and wait, a few seconds 4) Toggle CLEAR TAB on. 5) Toggle ON/OFF until a tab advances to the peel point and the TAB READY light illuminates.Your sensor has now been re-calibrated!Another thing to check is to make sure the tabs are threaded correctly! See photos below. Below Shows to correct way to thread the Accufast KT Tabber Correct Incorrect Do you need a KT?

Give All For Mailers a call at 866-430-2874 New and Used Accufast KT available! Need Need Replacement Parts? SuppliesForMailers.com has them! Need a parts breakdown / parts manual? Try Find the part, click on it and order! Need some help replacing the tab sweep? Check out Similar Posts: • Posted November 28, 2017 • Posted August 30, 2011 • Posted November 27, 2017 • Posted May 19, 2010 • Posted June 4, 2009.